I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
I have several applications that continuously scan on Bluetooth that have started exhibiting a new failure mode after upgrading nrfxlib from v2.9.0 to v3.0.2 ( https://github...
For our custom nrf9151 board,
The following is the prj.conf:
There are no pullups on any GPIO and for now, assume there are no peripherals connected, but there is a...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hi,
I would like to know the value of the Noise Figure for the nRF52840. How much dB is it? I am looking at the documentation of the nRF 52840 but could not find the value...
Hi Nordic team,
I'm currently working on a device onboarding flow using the nRF Connect SDK Toolchain v2.6.0 on an nRF52840 board . The onboarding process involves:
...
I am building the sample project C:\ncs\v2.5.0\nrf\samples\bluetooth\peripheral_uart, which supports MCUboot’s serial recovery of the networking core image on nRF5340DK. ...
My Power Profile Kit (PPK2) having issue after a firmware update. Now it's not even turn on the light when connected and with power switch on. I think I accidentally update...
My company does firmware consulting work. We have been asked to create a Green Power Device (Wall Light Switch) on the Nordic nRF52833 chip.
From our research It does...
I have make a PCB with a BLE5340PA module from Ezurio using the nordic 5340 soc, i want to programm the soc but it seem that there is no boot on the module.
Fortunately...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi all,
I'm working on an application using the nRF54L15 with NCS v2.9.0 and Zephyr RTOS. The device performs BLE scanning using the following parameters:
When deployed...
Hello Team,
We are working on nrf54l15 platform and using nrf connect SDK 3.0.2 We have added the support of DFU over BLE using following steps:
1. Added " CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
