The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I have a SPI Master and a SPI Slave. The Master will randomly pull data over SPI from the Slave. The slave will randomly generate events that result in data to be sent to...
I am using SDK version 17.0.2. The example code uses SPI.
The following changes have been made to the pin settings.
Questions
1. Pin behavior is strange.
...
Hello, Support team.
Our boards do SPI communication to read sensor data.
Basically It works well. I checked that It operates more than 5 hours.
But only one board...
Hi,
I have the following initialization for advertising:
The name consists of an acronym od three letters and a underscore e,g, XXX_ and a six digit ID. Like XXX_12E124...
Hi,
Is it possible to add four pairs of resistors between the debug signal lines and the connector as shown in the figure below.
Would such a connection not impair the...
The Google Fast Pair Service has recently been included in a number of Bluetooth peripherals (Headphones, fitness trackers, etc.) and has been getting rave reviews.
Has...
I am able to download simple blinky program on my custom board. It is working fine. Custom board is interfaced with nRF52-DK through P19. I am using embedded studio as IDE...
Hi, on nRF5340 I want to capture accurate timing of external events. I need a kind of real-time capture module to read the time period of a pulse train generated by a rotating...
Have a few questions about ble_app_uart example.
From the way I see it, it sets uart_event_handle as the callback, and every time there's an "event" that takes place...
Hello All,
Method 1: I am writing a test application to read the ADC data at a specific intervals(10 samples for every 5ms interval for every 50sec). I am using blocking...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
