Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello.
I'm working on disconnecting ble from the module.
I'm using the app provided by nordic.
I designed it to disconnect the ble when I press the button on the module...
hi.,
we develop a product that use nrf52840,and it need to suport usb dfu in windowns and mac.and also need achieve cdc communication .this funcation is ok in windows,and...
USED SDK: v1.4.99-dev1
USED BOARD: nRF9160DK
Received hexvalues above 0x7F (decimal = 127) are counted double in p->message.payload.len Any ideas what might be te problem...
We are trying to evaluate the BLE Mesh for a product range and are evaluating the nRF52832 for the same.
Working with the nRF Mesh SDK, I am facing some issues, which are...
Under the recommended operating conditions (page 611) in the nRF52840 datasheet, there is a note specifying:
Given a device (with SWD access), is there any way to detect...
Hello Sr,
Take a look below Error, when I run the demo code from
C:\..\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\multiprotocol\ble_thread\ble_thread_dyn_mtd_coap_cli...
Hi,
We have created an application with BLE multi peripheral where I have to put my chip into deep sleep mode by long pressing the tactile button & also I have to wake it...
In the nRF51822, there was a bootloder area, but in the nRF52810, there is no area except for Application, and the image is as shown in the map below, is that correct? --...
Situation: SES, SDK 16, nRF52832, no BLE.
I'm trying to use both the UART and TWI 0. TWI works fine with BLE and all the rest. However, when I enable the UART, TWI quits...
Our device has been in use for a year using the nRF52840. We elected to not load the 32KHz crystal on our board. Everything seems to work OK and we have no BTLE issues, however...
Hi,
I'm using nRF PWM Driver and I didn't find the way, how to invert logic of PWM. I would like to reach this behaviour:
If I set seq_value=0, I want to have
PWM...
Hello,
We are currently using the NRF52840 with SDK 17.0.2 with S113 softDevice. We have our own boot-loader implementation. Is it possible (advisable) to perform an Over...
