Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I want to move the UART on thingy91:nRF9160.
prj_thingy91_nrf9160ns.conf added the following two line.
CONFIG_UART_ASYNC_API=y CONFIG_NRFX_UARTE0=y
The asset_tracker...
Hi All,
I want to use DFU to update the firmware from central to peripheral over BLE , both central master and peripheral are nrf52840.
Central master can find unknown...
Good Day,
we are currently working on a project for university. For this project, we are using esb to transmit a continuous audio stream (i2s format). We sample our data...
I've read similar issues but none with this configuration:-
nRF Connect SDK 1.4.2
Blinky example
Trying to enable RTT logging
nRF5340DK board
Windows 64 bit host...
Hi,
I've come across a situation where when paired to Android 9 devices, the reconnect event that follows waking the peripheral fails. Connection parameters are
The...
For ble_gap_adv_set_configure_req_enc, is the document provided?
I saw " ">infocenter.nordicsemi.com/.../group__ble__gap__app.html" , it was not found.
Hi, There is problem that the including file from "openthread\third_party\NordicSemiconductor\libraries\fds" and already added its path to file...third_party\NordicSemiconductor...
Regarding the data encoding in Advertising, the order of the data is different depending on the SDK. Is there a problem in operation?
The confirmed function is as follows...
We are using nRF52811, is there any sample code support to set/save thread power calibration table/data to available non-volatile partition.
thanks, Webber
Hi there,
Can we please get an updated example for Appendix 5 in this blog ?
Specifically the DFUMaster_SPI and the bootloader_secure_SPIS. Ideally it would be compatible...
Hi!
I was trying the throughput example using two nRF5340PDK boards and I observed the throughput is very low, i.e. 1kpbs. I tried programming the cpuappns, but it didn...
Hello! Reading the following segment regarding Buttonless DFU with bonds from the documentation, I'm not clear as to the meaning of these paragraphs. It looks like two contradicting...
Hi
i am able to work with adc 0 for nrf9160 custom borad now i want to use adc 5 to adc 7 simultanuously can you please guide me to settings which i need to modify or a...
Hii guys ,
I am trying to pair two nrf52 bluetooth devices. How can we pair two stand alone nrf52 devices to send and receive data? Is there any example code to show such...
