Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi, I am trying to setup a mesh architecture, and I am not sure which path to take (Thread / Zigbee / Etc). The architecture is for the following system.
There will be...
hello, i am trying an example of a Node running multi-peripheral with ble_nus service. I have a question: Suppose when Node receives a packet from central A, Node will call...
nrf52832.
SDK14.2
Segger ES V3.34a
This question is probably best suited to an android forum (possibly).
We have a characteristic which is writable. When written...
Hello,
Our unused pins, 5 and 6, are not connected. What saves more current? Pull-up or pull-down or neither? These pins will never be used and are not tied to anything...
Dear nordic,
I have some doubts in nrf52840.
1. How this VDD_nrf voltage generate?
2. Is this VDD_nrf voltage only depend on Hardware or is itany dependency in software...
In the On Off Client Model in the nRF5 SDK for Mesh 15.0.0 (nRF5-SDK-for-Mesh/models/simple_on_off/src/simple_on_off_client.c) there is a check in the client callback handler...
I try to build and test my first time SES setup on Mac for further development on an existing nRF51 project and future nRF52 project.
I use SES for Nordic V4.14 and SDK...
Hi Nordic
I am looking at legacy code in nRF24LE1 that has to be ported to a new chip, nRF52xx.
The thing that I have come across is a strange thing in the datasheet...
Hi Nordics, I wonder is there any specification on IOT. I have seen the source code on IOT at nRF5_SDK_15.3.0_59ac345\examples\iot\tcp. But I don't know how to use it. So...
Hi all,
i am using:
- nrf52832 DK (IC revision 1 -> QFAAB0)
- nrf5 sdk for mesh v 3.1.0
- nrf mesh app v. 1.2.1 running on android 5.1/ second phone android v. 8.1...
On a NRF52832 based beacon I use to sensors, a SHT3 temperature and humidity sensor and a KX022 accelerometer.
I'm using the twi_manager library as it is used in the example...
I've made an application based on the SDK 15.3.0 ' Console over Bluetooth ' example:
https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-3-0/ble_sdk_app_cli ...
Hi, I understand that the Decawave UWB modules have nrf52832 Chip in them. But we are facing BLE issues (it gets disconnected and connects). We are using a Panasonic Tab containing...
I have nRF51822 AA with SDK 12.3.0 and SEGGER SES 3.10f. I was able to run and experiment with ble_app_beacon example, fixing known SES troubles, mainly with memory sections...
Environment:
BLE Slave Module: nRF51822, s110 v6.0, based on UART over BLE application example
If a peripheral and central is getting further and further, finally they...
