I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hİ,
I can connect to LTE. but somewhere which I think it might not be the signal, it can not connect and restart (reset). not return any error. if I change my location ...
Hi there,
I have purchased a Fanstel BU840XE device ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) theres the link. The device has...
Hi,
1. How can the read slave interval be reduced to less than 2ms: twi_master_with_twis_slave
2. Test environment:
DK: pca10056
SDK:nRF5_SDK_17.1.0_ddde560\examples...
Hello,
I am aware that there is going to be an update to the BLE stack and you are soon releasing 2.8.0. For NCS 2.6.0 we were using 239354 for the host subsystem and...
Hi,
I use Nordic nRF52840 BLE Sniffer Dongle and this works as expected in Wireshark up to version 4.2.7. Hówever, when I upgrade Wireshark from 4.2.7 to 4.4.0, the Dongle...
In Software Maturity Levels under Trusted Firmware-M , it is stated that only the minimal build is supported, while the full build is still considered experimental.
In Running...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
Hi
We are using the nRF51822 with the SoftDevice S130 V2.0.1.
The nRF51 communicates with another controller via UART with a special handshake-mechanism directly on the...
I am trying to use the external flash on my NRF5340dk to store and read data files. Raw IO from the spi_flash sample seems to be working fine, but I'm not sure how to mount...
Hi,
I use CAF LEDs with PWM. I have a timer that would make device wake up every 20 seconds with a CONFIG_CAF_POWER_MANAGER_TIMEOUT to make it sleep 2 seconds after waking...
Hello,
I’m trying to get an nRF21540 FEM working with a chip-down nRF5340 design under NCS v2.4.2. I’m able to enable the FEM at its default gain setting, but I hit a wall...
Hi DevZone,
I've see sample application nrf/applications/nrf5340_audio use tone.h for tone test, and I want to add this function to my project.
In nrf/applications/nrf5340_audio...
Hi, I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio as my IDE. I have integrated the Timer and SAADC peripherals into the...
Hi,
I'm trying to FOTA over BLE firmware of mcuboot using NRF52840DK. The project is based on the sample from Intermediate course - Lesson 8, exercise 3 (without the steps...
