In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
I am using nRF52820 and the SDK is nRF5_SDK_17.1.0_ddde560. When setting advertising data, I am trying to enter the chip's BD address for individual identification. Is there...
So, I follow the zephyr docs ( https://docs.zephyrproject.org/latest/kernel/services/synchronization/events.html )
and define an event as:
However I get the error: ...
Hello, when building the MQTT sample in the nRF Connect SDK, `getaddrinfo()` is returning only -2 when built for the nRF9161 dev kit. I'm using the onomondo SIM that came...
Dear DevZone Nordic Team,
I am currently working on a project involving the nRF9160DK , and I need guidance on how to operate and output GPS values in the debug console...
I am learning how to use MCUMGR. I generally understand it, but I have some concerns.
- The firmware with the private key can also be overwritten. Then it will not boot...
Hello:
We know that 45pin 46pin DEC4 can be connected to inductance to process the ripple of internal DCDC circuit. Then, may I ask which pin is the input power supply corresponding...
Hi,
Can someone please help me to understand how to implement secure boot on nRF52833 chipset?
How to secure root of trust, as once you remove the protection, entire...
With TAU set to 24 hours, when we wake up every 8 hours, everything works fine. When we extend to 12 hours, it takes longer than 10 seconds for a connection to be established...
I successfully enabled littlefs in mcuboot and read/write it successfully (due to project requirements), and then tried to enable littlefs in both mcuboot and app, operating...
Hi,
I am planning to design a new PCB and transition from using the Raytac module to our own custom PCB.
During my search, I found a design that includes an SMA connector...
Hi, What I noticed is that every time I want to flash the nRF9161dk I need to do `west flash --recover` for it to work. I am flashing from Mac M1 (Sonoma 14.5) with `West...
nRF51822QFAC SDK v10 S130
In the completed project it was necessary to make an update. It is necessary to switch off the softdevice and switch to its own Rx protocol. After...
Just purchased a nPM1300 v1.1.0, but it will not connect to my computer. I am using version 2.6.1 of nrf connect, v1.3.0 of the PowerUp app, and what I believe is the correct...
Once the modem is turned off (e.g. using at+cfun=0) - what will be the state of the MAGPIO pins? Will they be pulled to GND or will they float?
Thanks
Ulf
P.S. The same...
