I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi Nordic,
I've implemented an extension of the NRF DFU protocol using the "external-app" type. The transfer is stored in external flash, and can be approx 1MB in size....
Hi
I have tested direction finding examples successfully., by default parameters. Theses projects are used as "TX" and "RX" in AoA mode:
https://developer.nordicsemi...
Hello, following this question - https://devzone.nordicsemi.com/f/nordic-q-a/76417/saadc-tasks_calibrateoffset-shall-only-be-used-before-tasks_start-or-after-events_end-nrf52833...
How i'm supposed to check if the device is transmiting any data? I used nRF52833 DK as a sink and node of wirepas mesh network, added another DK and configured it as a regular...
Hi,
I'm making an firmware for the nrf52840 that communicate throw usb to a computer.
First I used the uart library that works fine but required the Jtag and Jling which...
I just cloned the latest zephyr from github and tried littlefs. However, the SPI pins have no traffic and CS line stays unchanged.
Is there something I forgot, since...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
