hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using nrf5340 kit. I would like to enable and test power management in mesh chat example.
1. Can you please tell me the usage of below config file usage.
#define...
Using: NRF52840, SDK 14.2, S140
My GPIO initialization code is as follows. This is the first thing that happens in main.c.
Here are logic analyzer traces of 2 GPIOs...
Hi
We would like to adjust the pin matching of our nRF52805 design since the measured S11 coefficients in Tx mode are not very good (well above -3dB). The values for the...
Hi.
I am testing a wearable device based on nRF52832 and it does not have a reboot button.
Sometimes the device gets stuck and does not appear on Bluetooth scans. Rebooting...
Hello, I'm in Zephyr OS build v2.3.0 and NCS v1.3.0. I need to reprogram UART0 baudrate at run time to 38400. After having obtained the uart node
uart = device_get_binding...
I want to transmit UART and Bluetooth through 12bit ADC 12k sampling.
I downloaded the following example and verified the ADC-UART AND Bluetooth communication. https://github...
Hi,
I use the nRF52840 chip, which is designed as a module.
I use nRF9160 DK to burn the hex file.
1.And i can use nRF connect to read the ic of the module.
But...
Hi there, We're using SDK 16.0.0_98a98e2. Our setup is a PC running BLE Central connecting to 2 nRF 52840 running as BLE peripherals. We use the provided BLE UART example...
Dir Sir or Madam,
I defined 2 properties in sensor_server mesh example,
Precise Present Ambient Temperature (0x0075) and Present Indoor Relative Humidity (0x00A7) ,
...
Hi,
I use sd system power off to go into sleep mode. I wake up with the help of a button. However, the 1 second wake up time is too much for us. Do we have a chance to set...
I am currently trying to send indefinitely large files over BLE. To do this I have a central and peripheral application running between 2 nRF52840's (one peripheral, one central...
Hi,
NRF52832, SD S132 7.0.1, SDK16, custom device, custom SW
The: custom device not bonded.
In my firmware I can run beaconing in parallel with connectivity advertisement...
Hi sir,
I encountered a problem while building Thingy SDK using segger. Here are steps what I did,
Downloaded "thingy_sdk_v2.1.0" SDK from this https://www.nordicsemi...
