Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
We have a PCA10090 board and I followed all the steps of the nRF Connect SDK to install everything, including the files from repository, SES, etc. All is ok but I can't find...
Hello, I am working on a project that uses nrf52832 and I need to put that device and in the system on mode. For that, I want to measure the current in the system on and system...
The PWM (Pulse Width Modulation) peripheral coupled with EasyDMA makes an excellent waveform generator. However it has one drawback which I would like to request be added...
Hi, i use the saadc example(triggered by ppi+timer) with uart to get voltage signal and transmit to central device( another custom nrf52832 board), and the central prints...
hi .eveyone. i use 51822 sdk12.3.0 , i want to dfu app code with uart, but not use bootloader_secure and experimental_ble_app_buttonless_dfu. i do not know how to develop...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s130 to using s140 in order to experiment with long range.
Besides changing...
I try to update firmware for nrf9160.
My environment is windows10 msys2 python3.7.3 run follow, (not success) ----------------------------------------------------------...
I've done this many times now and thought I understood the process.
Now despite following most of the advice in the dev zone, I'm stuck.
Any help would be appreciated...
I'm trying to develop from the Linux command line, using arm gcc tools, for the nRF52 Development kit, and can't get the startup assembly file assembled to an object file...
I am preparing my product for radio tests. There is a radio test example in the NRF5 SDK 15.3.0 that requires a UART interface that sends CLI commands to the chip. However...
Hi,
i am trying to read ADC value from my nrf9160 dev board, i can get the exact value upto 2.5v, if i go morethan 2.5v it decrease the ADC value. my values are
voltage...
I've used the nrf_inbuilt_key_write to store certificates/keys in the past, but I am still unable to do it using the "AT%CMNG" modem command.
I can list and delete items...
I attended Nordic Tech Tour - San Jose (Cupertino) on June 11. I did not receive a link for the presentations, as was communicated. Please advise how I can get the Tech Tour...
The BWG832F DK Bluetooth Gateway comes with a board that says that it can be used to program the Bluetooth module. The software recommended for this is the Nordic nRFgo Studio...
