I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello,
We are using nRF52832xx_aa controller for our product, the sleep current consumption is approx 2 uA @25 degree Celsius which is fine with me. But when the temperature...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
Hi everyone ,
I have a custom PCB using nrf52840 and i measured the current consumption using PPK(power profiler kit) . The sleep current value that it show is 4.5mA.
...
Hello,
I want that two devices can connect with each other and only each other . To do this i wanted to use whitelist on peripheral side but i found that i could use filtering...
Hello.
I'm using nRF SDK 15.2 together with the Nordic 802.15.4 driver ( here ).
When trying to add the libuarte module to my project I started having mysterious issues...
Hi there,
I'm trying to get a one button nrf52832 device to behave like the following:
1. Button press short: RESET or WAKE (depending on POWER state)
2. Button press...
Hello,
I got problem when I press button program go to interrupt mode, but than all stops because of vektor catch. Im using ble_app_uart example.
Here is my main function...
I guys, I m trying to use the nrf52840 protocol in order to send an interrupts between two boards.
Looking at the examples provided in the SDK i didn't understand how to...
Hi, I have a particular issue that happens intermittently, I was hoping someone here has come across the same issue and possibly knows how to fix it.
My Setup:
Using...
Hi
I am trying to add manuf data to ble_app_hts sample advertisement but without success:
static void advertising_init(void) { ret_code_t err_code; ble_advertising_init_t...
nrf52840 last version of SDK Hello I need help. I want to start ble_adv and then stop with a button signal and start again with another button signal. The idea is
Loop:...
Hi,
I am using ble_app_uart example and want to detect the read evant/ call back. Kindly help me how to register a call back function of a read type characteristic. I want...
