Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
Just verifying to be 110% sure:
The TRACEDATA1-4 pins may be used as ordinary GPIO pins when no trace-functionality is configured for the debugger? So even if a debugger...
Hi,
I have a PCA10040 connected with some wires to an external I2C device and I need to poll data from the I2C device and send it over BLE, also updating the advertisement...
Hello,
I'm looking at the different way to control / dialogue with nRF9160 module.
I know it is possible to send commands through the UART port or through the cloud, but...
Hello Support,
I have developed one device based on NRF52,it has interfaced 4 sensors.It's working fine.
Now i want add one feature is that if sometime connection lost...
Hi,
I'm doing research on Bluetooth Mesh for which I built a Mesh system for testing throughput. So currently I am sending messages at the max speed (every 25 milliseconds...
Dear Nordic,
I am trying to do the following;
nrf52840dk will be ble central
ios will be peripheral
ios will begin to advertise then nrf52840 will connect
...
We are using SDK 15.0 and Softdevice 6.0, nRF52832
The question is :(1) We migrated the example "ble_app_hrs_freertos" to "ble_app_uart_c",luckily it works ;(2) But when...
HI,
I am using NRF52832,SDK15.2
I need to work on ultra low power consumption because My project related to Health care, Fitness tracker and HOME IOT mesh network.
for...
