I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I did proper connection of lcd to nordic board. and did proper contrast setting.
But not able to display anything on lcd.
i am using JHD162A 16x2 lcd.
www.brodie...
Hi guys what's the latest revision of "nRF51822 Bluetooth Smart Beacon Kits"? that's the beacon with the battery, the revision is written on the envelope.
I thought it...
Hello everyone,
The more I learn, the more I learn how much more I have to learn.
I am pretty new to embedded systems development. I am tasked with developing an nRF52...
Hello,
I've had to redesign my bootloader and I am now stuck with a problem that I can not solve. I need to know the correct workflow for switching from bootloader to application...
I use the nrf51822QFAA, and s110 v8.0.0.
now I need update the application,i have the keil created hex file,
How can I create the ZIP file use the application hex file?...
I have built a PCB that includes the nRF51822. I have AIN7 reading an input voltage that I measure on my DMM at 269mV.
When I measure the voltage through the nRF51822's...
Hi, I have an application where I am recording button presses using a beacon-like implementation. The button presses represent start/finish events for a race and are communicated...
In my setup, i have a Node with SD130 as peripheral to Smartphone and as a central to a BLE peripheral.
I need to store some Unique ID about the Smart phone and a Peripheral...
I find out that
The s110 can only connect to a single
central, but is able to do
non-connectable advertising while in
that connection
by here
So is this...
Hello,
I have a problem with the sd_flash_write function. It HardFaults on me and I can't seem to find out why. The Addresses are 4 byte aligned...
The function is called...
Hello,
I have written a timer driver with timer 0 without SD and used 24 bit mode and it is working.
But when I used the same driver with softdevice and Timer 2 and...
I have a problem enabling TIMER1:
If the prescaler is set between 16MHz and 2 MHz the firmware fails to enable the SoftDevice, even if I didn't manage TIMER0, but TIMER1...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130.
Does anyone tried...
