Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Unable to find enough information to convert the raw values obtained from Thingy53 for RGB components.
Referred to BH1749NUC datasheet, Thingy53 sample code
Hi,
I am writing a custom i2c driver for an evaluation, when I ran the same i was getting exception:
during troubleshooting i scraped the entire custom driver and...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I'm applying an application firmware update by calling fota_download_start_with_image_type with DFU_TARGET_IMAGE_TYPE_MCUBOOT...
The Radio Notification Callback functionality found here is exactly what I am looking for. However, when I try to include the associated header < bluetooth/radio_notification_cb...
Hello everyone,
for my project I had to develop a new driver for the Kinetic 2026 LED driver.
I have attached the driver to my project like this in the Device Tree like...
I have some nRF52840 USB Dongles that I would like to turn into a generic BT receiver for SBC's that does not already have BT/WiFi chipset onboard. I was hoping I could program...
My laptop does not detect my dongle after I program it through nrfConnect. I am thinking that maybe I have to reflash the pca 10059 firmware, but I do not have any nrf development...
Using nRF5340 hci code, I've been able to get a device that connects and authenticates with two central devices. However, after connecting with one central device, I no longer...
Dear Forum,
Knowing that nRF9161 SoC contains two microcontrollers: modem microcontroller (MCU) and application microcontroller (MCU):
1. Is it possible to check what...
I am developing a touch keyboard. (using SDK 17.1.0, nRF52840) Of course, this product connects to all OSes such as Windows/iPad/MacBook via BLE. However, there are keys that...
Hi there
For proper playback of LE Audio, it's required to get the current time of the Bluetooth Controller.
In the LE Audio examples (nrf/application/nrf5340_audio) on...
Hi,
I'm trying to get the PWM to work to operate a vibrator connected to the nRF54L15 PDK. I'm basing my activity on lesson4 - pwm as I'm also new to Zephyr (but experienced...
Hi Community,
I made a custom board based on thingy53.
the custom board can be flashed with nRF5340-DK, I see the " merged_domains.hex " is flashed.
Also tried with...
Hi
Default value of NRF_SPIM0->IFTIMING.RXDELAY = 02 based on the datasheet, but it always shows 0x00 on debugger and I can not rewrite it.
Has anyone entered the same...
