Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
Hello,
when I open any example Project from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with Keil MDK v5, I directly get the Error Message "Cannot...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
After updating nRF Connect and the Programmer app, DKs aren't being recognized when clicking on Select Device.
Tried both with nRF9160 and nRF5340 DKs and neither was detected...
I'm working with the PCA10040, the SDK V11.0.0. and the winbond memory flash W25Q80BV.
For the SPI connection I'm using the the SPI2 because TWI0 and TWI1 are being used...
Hello
First of all, I`ve been spending way to many hours trying to figure this out, so I decided to open this ticket. I am new to microcontrollers in general and the Nordic...
Hello:
I'm new on nrF52832 development. I did some tests using nRF51 and so far so good. However I received a few samples of E104-BT5032 from eByte http://ebyte.com/product...
Hi,
I have 2 SES projects that both require softdevice plus application.
One of the projects combines application and softdevice into the .hex file that is generated...
HI
I am Programming in Keil IDE and I am using ST link v2 like debugger, but in Keil shows this problem "internal command error"
what is the problem? I was thinking...
I'm trying to build support for uart async api by adding:
CONFIG_SERIAL =y
CONFIG_UART_ASYNC_API =y
to my prj.conf. Without CONFIG_UART_ASYNC_API the app compiles...
The nRF Connect Extension for Visual Studio Code was recently updated to v2021.10.103 but, unfortunately, a problem mentioned in this post still exists: "Unknown board" issues...
Hi,
In the documentation for the nPM1100, in the section " Charging indication (CHG) and charging error indication (ERR) ", there is a schematic for connecting ERR/CHG...
HI.
is my first time to using Nordic devices, and I'm going to program nRF52840 to medical product,(oximeter, gyroscope, etc.), I am using a dev, module basic, only to test...
Hi By mistake I closed below but the issue not resolved yet.
https://devzone.nordicsemi.com/f/nordic-q-a/81276/agps-example-question-related-to-psm-command-disablement ...
