Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
Hi team
I did follow the getting started assistant to set up software tools and clone sdk ncs 1.3.0.
Verified successfully at getting started assistant, too.
But, when...
Hi
I have some issues with nRF52810.
I am trying to use SPI as a Master on a custom board. I saw here that nRF52810 does not support legacy SPI : https://devzone.nordicsemi...
Hello,
We are adding BLE scanning to an ANT product.
We have been using SDK 10.0.0 from the beginning, so we use the Example below.
SDK 10.0.0.0\examples\ble_central...
Hi Supportor
I have two board, if I didn't set the gain, which used default of SDK, one board output value is 0x2f5, another output ADC value is 0x266.
I set the gain...
Hello,
I'm having issues with what I believe are interrupts, if I use the bootloader.
I'll give a brief description of the issue I faced, and then I'll state how to reproduce...
Hello,
Is there any documentation available that specifies what version of nrfutil is required to create DFU packages which are compatible with a SDK and/or soft device...
Hi
I am using NRF52 with 512KB flash, and with SDK15.2
I am not using DFU
I tried to protect the program flash pages using "sd_flash_protect".
I tried to protect pages...
Hi everyone,
Currently I'm using Android Nrf Mesh Library 2.4.1 for provisioning device into network.
I face the issue which can not be found why to fix this error.
...
I cannot set CONFIG_POWER_OPTIMIZATION_ENABLE to yes in the master branch. It leads to deadlock in at_cmd_write() because that ends up getting executed in the socket_thread...
I copied the slm application into a directory outside the SDK (e.g. C:\temp\slmapp) and I launched a command prompt from the nRF Connect's tool chain manager. Then I navigated...
Hi, I was trying to interface nRF 52840 with a SPI based NOR flash (IS25LP064A). I am using SPI example in 16.0.0 sdk version. But i am not able to read the device id as this...
