The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello,
We are using the SPIS on the nRF52832. We are seeing a higher than expected consumption when it's enabled and not used.
I measure around 7uA extra when enabling...
Hi:
I test the system off mode, I attached a micro vibration sensor. Pulse generated when shaking as follow.
the button config is BSP example default(toggle) , i try to...
Hi,
I am testing the blue_app_uart example and I want to send data
from my smartphone uart terminal app,back to the nRF52840 DK,
Nothing is being received by the segger...
In the latest Mesh SDK, nodes are subscribed to a GROUP address. In previous versions - 2.0.0 I believe - you could also send to a predetermined node.
I am trying to figure...
Hi I am reviewing the nRF52840-DK hardware documentation to make boards with good antenna performance.
Q1. I have divided it into three areas as shown below. Is my understanding...
Hi,
I have been trying to use Keil MDK's Middleware File System with my application. However, when I try to set the Software Component under Manage Run-Time Environment...
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi!
I am using the Segger embedded Studio with PCA10056 successfully. Now I have to evaluate LARD DVK-BL654 (because it has external antenna). I found a guide which says...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...
SDK15.0 whitelist hardfault
when setting the sd_ble_gap_device_identities_set using the iOS nrfConnect the non DK board hardfaults.
On an android device all works fine...
Hi,
I'm adding some custom buttons to the NRF52-DK and I've been playing around in PCA10040.h. So far, I have everything working with 4 buttons. The DK can connect to...
Dears,
Now I am using nRF5_SDK_15.3.0_59ac345 for my project on nRF52810.
I found a bootloader example at
\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble...
hello, I am trying to integrates saadc & bluetooth because in my project adc sample values are comming from sensor & these values is send through bluetooth_uart app. so can...
