Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
I use nrf52832-AA, S132
I use Fstorage from 0x68000 to 0x73FFF in flash memory.
Reading or writing data from that memory.
It doesn't have any problem working normally...
Hello Everyone,
I am newbie to nordic BLE environment. This maybe a silly question.
Currently I am using nrf51 DK with SDK11, S130.
Data to be sent through SPI:
...
Hi,
I was trying to add generic onoff server model to the dimming server example in order to On/OFF and Dim the LED on the nRF52 Dev board using nRF Mesh App. I added all...
With 100 battery powered bluetooth long range slave nodes connected to one master. To increase battery lifetime, Is is best to connect/disconnect all slave nodes to the master...
Hello,
I have the following scenario:
The device boots and starts to advertise.
When the central (android phone or iPhone) connects, peripheral requests bonding and...
I am using sdk 11, s130, nrf 51822.
Before getting into the question I ask in the title, I would like to ask this first:
1. Is it correct that every time I call pm_peer_delete_all...
I'm trying to integrate buttonless DFU in BLE app uart example. I added the file: ble_dfu.c, ble_dfu_bonded.c, ble_dfu_unbonded.c in the project. I added the following folder...
It's battery operation so I want to know how to setup 1sec timer and goto sleep_mode(power_down) after 1sec beacon scanning.
I'm using WDT to setup 60sec WDT reset so I...
Hi,
May I know what is the hardware layout for measuring external voltage using SAADC? I may not be understanding the infocenter or the datasheet for setting the external...
In the `Serial Interface`, the `Bluetooth Mesh Packet Send` command does allow specifying the `Time To Live` (TTL) for arbitrary packets, but there is no field for `Retransmit...
Hello, I have a question.
1. When ancs is reconnected, the machine will be reset, and the software will catch the log as follows.
As long as there are a large number of...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to know what would happen in the following situation.
During central and peripheral...
I noticed that in SDK SES projects, the linker file is generated every time the project is build. However, there is no memory map file specified, only a section placement...
I program in nrf52840 using thingy sdk
I succeeded in receiving the motion service.
The output speed of some motion services is too fast. such as raw, heading, gravity...
