Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
In my project, there is a device lock up and I found the problematic point that a debug log using nrf_serial_write() in critical region.
I think it is not a good idea...
Hi there Devs,
My app is based on ble_app_blinky_c where I added a couple TWI sensors where check periodically every 10s and also scan for peripherals about every 10s...
Hello mates, Im trying to run this proyect:
nrf52-spi-i2c-master-ssd1306 ( github.com/.../nrf52-spi-i2c-master-ssd1306 )
I have the display and that kit development...
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v2.2.0 on my nrf52832 dev board but this gives the following error "boards.h: No such file or...
I would like to know if Nordic has implemented software support for CryptoCell-312 (nRF5340) in the latest master branch?
Right now I am able to use mbedTLS "frontend",...
Hello All
Please tell me about nRF Connect (iOS).
When the module and nRF Connect (Ver 2.0.1) are connected using LESC, they will be disconnected after bonding is completed...
I am using the ble_app_uart example and I am having a hard time finding the function that writes a UART message to BLE from the Nordic to the host. uart_event_handle() seems...
Hello All,
I am working on nRF51822 use SDK nRF5 12.3.0 version in IAR workbench.
I am write data in the flash so for that i follow below steps,
Step 1: press button...
So, I need to send and receive a data frame with 39 Bytes with a system Dongle-Arduino(with a nRF24L01 module).
My problem is, I tried to configure Dongle to communicate...
Hi,
I cannot update the firmware on the nrf9160 MLM1 Preview development kit we have. Is this possible? or is the devkit voided for the latest nrf connect and nrfjprog...
Good afternoon everyone,
I'm trying to make a working application for the BLE NUS example but with the support of FreeRTOS that is MANDATORY. I work with KEIL. I started...
with NCS v1.3.0 is there a way to turn off partition manager? I want to be able to build my app and mcuboot separately and not use partition manager at all.
Is it possibe to upgrade nRF52-DK on board programmer to program nRF52840? I already have this nRF52DK but in final I found that 52840 will be better choise for my proyect...
Hi, I am reading the datasheet of both the sensor. but i2c register are different.
I am currently work on vl53l1x. please give me the response as early as possible. thanks...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
