Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am creating a BLE peripheral device which I want to test using the automated testing feature of NRF Connect. I have connected a android phone to my windows PC and the phone...
Hi.
I'm trying to send data through L2CAP from Cypress BLE evaluation board to nrf51822 chip.
It seems that Nordic's API for L2CAP is much simpler than Cypress', but I...
I noticed some suggestions to add Static Passkey.
I have 10040 nrf52832 sdk13.0.0 s132
The server has no IO, so cannot enter passkey from it.
Is there an example...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
I need to do the following when assembling a device with nrf-52 at the factory.
Add firmware onto device
Add a unique serial number for the device
Print a sticker...
i have added pwm into proximity profile example and now i am able to make beep using buzzer with pwm library.Now i want to make some sort of Tune instead of beep.
Can any...
hi,all
i use ble-sniffer_win_1.0.1_1111_Sniffer.exe,but it note as follow:
and Why sometimes not get the connection of the data? Sometimes it stop 60 CONNECT_REQ...
Hi
I use SD310 and nRF51 in SDK10 and The Ant is set HRM_MSG_PERIOD_1Hz.
I integrate a heart rate module by I2C and the heart rate data is only all I got.
But the Cell...
Hello,
while I already managed to solve a couple of problems regarding a proper handling of the DFU procedure in my previous topic here , there are still 3 problems that...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
hi,
i am newer here.
i am confused in nrf_gpio_pin_sense_t i.e. NOSENSE, HIGH_SENSE, LOW_SENSE.
where is use of this feature ?
why it is required instead gpio_input...
