Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi, I'm getting an error saying that "ble_link_ctx_manager.h: No such file or directory issue"
This is the main.c file:
Also, I have attached the snapshot of my project...
Hi!
I'm developing for nrf52832 using zephyr. I'm using the nordic hal driver in order to use the PWM with EasyDMA. The PWM is used to control a piezo buzzer. The PWM is...
I have very advanced project based on nrf52840dk for dev and custom boards for prod.
The development environment is based on zephyr build dockers. Zephyr is 3.5.0.
I would...
Hi,
I am having a hard time for days now trying to get the MCP2518FD working on a nRF9160-DK board. This device, embedding CAN transceiver and receiver, is accessible through...
Hello ,
I have a few questions about the connectivity bridge on T h i n g y : 9 1 . I 'm currently working with Bluetooth data on the nRF52 SoC and I need to transfer it...
I am building both the IOS and Android version of nRF Connect Device Manager and I am able to bootload/update my application.....but
But, we have external memory and we...
Hi there,
I want to manage certain devices that have an address and a value. I would like to dynamically add and remove devices from my data structure. I believe that using...
nRF52840-Preview-DK LED5 is off, J-Link Error.
I press IF BOOT/RESET key then poweron the PDK, no BOOTLOADER removable disk drive letter appears, I have installed the driver...
Hi all,
I am developing a sidewlk application as a replacement for LoRaWAN recently based on the sidewalk protocol implemented in the nRF connect SDK. I would like to check...
Hello,
We are currently manufacturing products using the nRF52840 with the nRF5 SDK. We are planning to develop new products using the nRF Connect SDK and are currently...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
Dear Nordic DevZone community,
I am currently grappling with a challenge involving the transmission of data from an NRF52 device to the NRF Toolbox app through BLE.
To...
When I build some example (e.g. samples\bluetooth\direct_test_mode) with NRF Connect SDK Toolchain v2.6.0 and NRF Connect SDK v2.6.0, I get the following errors: warning:...
