Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I would like to implement ble mesh direct forwarding feature in my code but i am not finding zephyr library for that. Is there any possibility to get link for zephyr direct...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
Hi All!
Hope you are doing well!
I am using nrf52833, NCS 2.3.0, Want to minimize the current consumption by sleep mode.
For this, I disabled the UART and SPI and the...
Hi
I have been studying the nRF Connect SDK and taking the courses at Nordic Dev Academy. In the Zephyr Fundamentals course, as I don't have the sensors used in lesson 6...
hello.
We're now planning to migrate our firmware library from nrf5 sdk 17.1.0 to stand alone nrfx v3.xx.x.
All our products are made with nrf5 sdk 17.1.0 using ses. ...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
I'm working with the nRF7002DK board using NCS version 2.6.0 . The internal flash is full, so I need to perform BLE DFU using external flash. Is there a sample available for...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
