Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello
I have 2 devices ,a central and a peripheral on a custom nRF52840 board
Using Zephyr SDK 2.5.0
The distance between the devices is 10.9 meters. When TX power on...
Hello,
We have nRF52833 on the custom board, now we want to do DFU over Bluetooth. During my initial research reults with following questions:
If you use 1. " nRF Connect...
Hi, Everyone
I have space constraint in my round PCB for RF section where i have take referance from thingy91 board and choose the same components exept mcu is nrf5340 claa...
Hi,
I have a request to port an old code into Zephyr. The code uses a proprietary protocol and the radio has been developed on bare metal under a nRF52832 chip. There is...
Hi all,
I am evaluating ANT+ features in nRF52 DK board and I am using nRF5_SDK_17.1.0_ddde560 SDK.
I need to implement ANT+ Bicycle light profile (LGT) in my device....
Hi.
I'm developing a ble module now.
I have a question about time out, interval among BLE init Advertising.
As shown in the picture below, time out (in units of 10ms...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZED)
NCS v2.4.1
Hi,
I am working on Tunneling cluster handling as that one...
Development environment: ncs 2.6.0.
my application need BLE-DFU, so i added multi-image support to my project.
the pm_static.yml is the typical default system configuration...
Hello,
I am working on a SWD flasher for nRF52 chips. I try to perform basic commands like flashing a firmware or reading flash content. I wanted to use FICR informations...
I am using NCS V2.6.0 and using zephyr there is no examples to measure battery level using saadc we can measure the battery level right? I used LEDs to indicate battery level...
Hi, I'am working on a design with nRF7002 and I need add WiFi antenna NN03-320 from Ignion and when check the datasheet of the builder of the antenna I see that the pin 4...
Hi there,
Is there any drawback or limitation in the S140 SoftDevice (v7.3.0) if a connection (as master) stays open for a very long time (weeks)? I mean, there could be...
Hi,
I use our customer board that enable the i2s to the DAC to speaker. However, i only verify the play a wav file directly that seems work normally but our target is playing...
which sample is best for me to verify the central/peripheral communication using nRF52833 for nRF52 serial.
I have two nRF52833 DK board, I need the board2board communication...
