Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
According to the Nordic infocenter here
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf9160%2FCOMP%2Fnrf9160%2Fnrf9160_operator_certifications.html&cp...
I am using nRF52840DK for working on my application. I use nRF Connect SDK v1.9.1 to run example and build application. I use VS code to build the application. I am working...
HI
Saw the youtude video: https://www.youtube.com/watch?v=dpvNXQiLbh4
For BLE Audio Broadcast mode, could i check how many channels of audio can be broadcasted and selectable...
I'm developing firmware for a custom board developed with the nRF5340. We opted to use RTT as our logging/shell output as opposed to UART thanks to pcb size limitations. I...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I'm trying to build the nRF5340 Audio sample application for the nRF5340 Audio DK board and get this error message when creating the project:
Any thoughts?
Regards...
I'm trying to migrate from the nRF52832 to the nRF52833 using the same exact code, but the nRF52833 does not go into low power mode. The nRF52832 consumes 100uA with the nRF52833...
Hello, I have successfully connected two NRF5340s using central_uart and peripheral_uart and can send messages to each other. But I don't know how to test the data rate.
I have an implementation that is using a PWM output to drive a LED. It has been observed that when the LED is on in a constant drive state, fixed PWM output train, the LED...
I would like to communicate at a speed of 1ms or 2ms if possible, as I need to make a gaming mouse with as little latency as possible. To achieve this, I plan to use the nRF52840...
Hi Team,
could you please help us how to remove service change characteristic?
Also please share us how to SET PHY as a constant "BLE_GAP_PHY_1MBPS" ?
please suggest...
The following code got NRF_ERROR_INVALID_STATE. What is meaning of NRF_ERROR_INVALID_STATE? And when will NRF_ERROR_INVALID_STATE generated?
err_code = nrf_drv_gpiote_init...
Dears,
The customer wants to know that the Thingy53 evaluation board can calculate the 3-axis acceleration,angular velocity,magnetic field, these 9sets of data into "quaternion...
I want to remap SPI0 pins from default (P26, P27, P28) to another ones (P08, P09, P10) on PCA10040 under nRF Connect SDK. But I stuck into a problem: SPI module seems to work...
Hi,
I just go a question about when to use the nrf_moden_lib_shutdown(). Is it necessary to use in this code case? Since I've used lte_lc_power_off().
Regards,
Elia...
