Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello!
I flashed the light_bulb example(NRF5 SDK v.4.2.0) hex to an nRF52840 Dongle using nRF Connect.
After reset, LED2 lights blue.
I do have an existing Zigbee network...
We have been using ble nus service which is working very well.
There are more than 100,000 bytes of data to be transferred each time.
We were using BLE_NUS_EVT_TX_RDY...
Hi I made some changes in the chat project that is found in NRF Connect SDK and when I build the change project this error occurs
kobj-types-enum.h: No such file or directory...
Hi,
I am writing after searching for an answer in this forum but without success.
I am not sure to understand the purpose of ble_app_proximity_coexist? I understood that...
I'm developing the nRF5340DK, would like to use the P0.04 (AIN0) pin to get the NTC thermistor value. but bind the device is fail.
the parts of the "source code".
/*ADC...
I'm trying to run your direct test mode code on the nrf53. And verify that the uart pins are working correctly. What is the best way to debug and verify this?
gdb seems...
Hi everyone
I'm looking for a way that I use the libuarte example with two UARTEs: one for receiving data, and one for sending data.
I tested serial uartes example in...
Hi, dear Nordic & all：
I just try to upgrade applicatiion via usb secure dfu on nrf52840DK, but failed to do this, the fellow is my environment, reference and steps: ...
Hello
I want to add a UICR section. but I don't know how to add a custom section in ncs(also zephyr).
I have researched about this for days and I've found zephyr code...
We have our own module using the NRF52832. We are using S132 V 7.2.0 We realized the ICs we bought had different revisions. One group is QFAAE0 and other group is QFAAE1....
I loaded the BLE peripheral HRS example from the Nordic SDK 17.0.2 on an nrf52840 DK. I connected a PPK II while connecting the peripheral using an nrf52840 dongle and the...
CAN-bus shield uses the one at the URL below.
https://www.seeedstudio.com/CAN-BUS-Shield-V2.html
I want to check if the SPI connection is established correctly.(CAN...
The /v1.6.0/nrf/samples/crypto/rsa project on NRF5340 returns the following error right out of the box. psa_generate_key failed! (Error: -134)
I have installed the SDK and...
