Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
In PCB phase of the product, I used mt8852b to conduct the ble measurement test,When assembling the finished product, I want to verify that the Bluetooth connection is good...
Hi Nordic team,
Summary: Shall we get nRF5340 based BLE mesh demo to test data relay from one node to another node.
Details:
We requires BLE mesh demo sample for testing...
Hello guys.
We use NCS v1.4.2 and Zephyr RTOS to develop the application code for our nRF52840 SoC.
Thanks to your support, we were able to use Zephyr ADC APIs and take...
I want to control the connection to send data for about 100ms, but the service discovery process takes about 300ms. When the service characteristics are known, I want to inform...
Hi, our application uses a nrf52840 module and a nrf52840 dongle. ( sdk15.0.0) in the application.
The central sends data to the peripheral continuously on an event. When...
I am trying to do some power measurements on the nRF5340 using the power profiler.
As suggested in the guide here, I am removing serial support to reduce power consumption...
Provide your AWS credentials page for Asset Tracker Cloud Example for AWS mentions sub-accounts. There is absolutely no such thing as a sub-account in AWS. The page is totally...
Hi.
I've been working with the nRF52840 for a couple of months. I started working on SEGGER IDE, but I've found that it was quite difficult to understand the behavior of...
I played around with the SAADC sampling A4 pin. When I connect to GND, I see negative values sometimes. If I connect to 3.3V I see value 235/236 which is, what I expect. ...
I have 2 device gateway and nrf52840 board.
Can i get zigbee distance?? I think RSSI data is possible. Right??
If you can measure the distance between gateway and nrf52840...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
I should not be asking this question here but it should be documented! SoftDevice s130.
A possible error I can get when executing sd_mutex_acquire() is NRF_ERROR_SOC_MUTEX_ALREADY_TAKEN...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
