hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I want to change DLE/MTU in udp (IoT) example in order to test throughput with max mtu, is it possible?
The udp example does not contain nrf_ble_gap library, is it possible...
Relative newbie here. Would like to interface an Arduino MCU (AVR 328p/32u4, etc) via UART protocol with a decent range (50-100m open air) nrf 52840. I found the Fanstel BT840F...
Hi,
I have been struggling with this for 2 days now, and I cannot get my head around the problem.
I want to send data from my nrf9160-dk to Azure IoT Hub via the sample...
Hi,
I'm using 51822 QFAC SDK11 S130. The 51822 will receive a group of 18 bytes data from the phone. I'm facing a strange issue: every time after the BLE is connected, I...
Trying to run the experimental nfc pairing reference on a couple of 840 DKs for Bluetooth pairing as it's shipped in SDK 17.
Successfully compiled the micro-ecc make files...
Hi,
I get sporadic softdevice assertions at the address above. I am using S132, SDK15.2.0 on nRF 52832 custom board, and the problem started when I added LoRaWAN functionality...
Hi,
Recently, we were trying to support the HID device OTA function.
We have make an user control panel which could read the device FW version via driver which communicate...
I am starting with the Zephyr sample "peripheral": developer.nordicsemi.com/.../README.html
This sample started out with a Heartrate Sensor Service and a Current Time Service...
Hi,
Just a general question, is there a way to find out the exact size of the advertising packet? I'm using nRF52832 to connect to a smart phone. I was curious if there...
Hello, I try to read from IM69D130 (as microphone) by nRF52832 (SDK 16) , And I work with PDM driver of nRF52. It seems it cannot read the data correctly. Here is my function...
Hi! Reading the documentation on NRF_PWR_MGMT_CONFIG_DEBUG_PIN_ENABLED, I'm left with a few questions.
1. Will this pin be set in all system sleep states? i.e System on...
Hello Everyone.
I'm getting falls values on the power profiler, I just connected a 1K resistor across the External DUT and the voltage is 3.6V so expected values should...
Hello Everyone,
I have done I2C communication with Grid Eye sensor (AMG 8832) using twi_master_with_twis_slave (nRF5_SDK_12.3.0_d7731ad) example program. Now i want to transmit...
