Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
Hi .......Clan
I am planning to make chatbox mean chatting (transferring the messages) between the central and peripherals even peripheral to peripheral , and device peripheral...
Im using MCP6S21 amplifier which takes input from some I to V converter and output of amplifier is connected to nrf52832 via I2C pins so how to change or vary gain of amplifier...
I am having a problem running MQTT_Simple on my nRF9160 DK.
The COM Port shows the following:
***** BUS FAULT ***** Precise data bus error BFAR Address: 0x4002a514 **...
Hi.
I am using the nrf9160 with the latest firmware and with all the instructions followed, I get this error . Faulting instruction address = 0x3648 Fatal fault in ISR!...
Hi,
I am working on mesh bluetooth using nrf52832 with PCA10040 , I used example from nrf5_SDK_for_Mesh_v2.0.1_src , my questions are
1.How many bytes(Max and min) can...
Our device allows only one device to pair and delete the original pairing information when there is a new device paired. Restore the original pairing information if there...
Hi,
I am using the nrf52832 dk for my project.
I am using the RX characteristic of the NUS example to send data from the phone to the dk.
In the same code i am also...
I tried to build the "nRF5_SDK_15.1.0_a8c0c4d\examples\crypto\nrf_crypto\aes\aes_all_cli\pca10056\blank" source code but I got the following error,
.\_build\nrf52840_xxaa...
Hello,
While i am trying to find the definition of SER_REQ_ENC_BEGIN(SD_BLE_GAP_ADV_START); it is there in the file ble_gap_app.c
When i right click on that function...
What is the difference between nrf5232, 1.8V and 3.3V power supplies? What should watch out for when replacing a 3.3V power supply with a 1.8V power supply?
Hi,
I'm developing a central application and I want my central to read the device name characteristic from 3rd-party peripherals. I do not know the length of the data in...
Hi,
I've been trying to develop a custom service for a Bluetooth application. This custom service (called ble_dts - Data Transfer Service) has two characteristics - Spectrum...
Daer sir or madam
I am the personal software engineer and want to check and receive the best answer about my question. If I use BLE to connect the both smartphone and device...
My hardware only has one spi slave and one spi master. So can I just set the spi slave miso pin as output in spis_init function? If can not, can I set the pull down resistor...
