Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Dear sir,
The current BGA ball size is 0.3mm. What is the recommended VIA hole size for the inner pads for routing the signals out from IC ? or How large of the via in...
Dear Company,
I would like to ask about start-up time of this product nFR24L01
Max 1.5ms start-up from power down mode
Max 130us start-up from standby-I mode
1...
Hi, everyone
how to increase the peripheral link count in multi role lesc example . even i have tried with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT by increasing the count, i am...
I have followed the dfu bootloader instructions for dfu secure ble example in both sdk 15.3 and 15.2 versions. I copied pca10056 folder to pca10059 and changed the board definitions...
Hi. I'm using nRF52832, SDK13.0.0.
I'm developing not only peripheral side but also central side.
I already made peripheral side referring to DFU example code.
But i...
I was trying to measure the current used by the nRF52840 on the DK. But it seems like i have messed up.
The debugger LED does not light up
The nRF52840 SOC seems to...
hi team,
i have downloaded image transfer demo source code in github. installed it in sdk 13.0. the softdevice is 5.0.0-2. i am using nrf52840 pdk. the code is successfully...
Hi Al
I'm implementing multiple channel ADC with PPI
sampling multiple ADC channels with PPI, adc event triggered adc_event_handler as many times as channels (instead...
Hello everyone. I'm working to a project with nRF52840. I'm developing the code in SDK in SES ide. The task i want to perform is transfer data from the memory of nRF52840...
Hi,
I am using the S130 central pairing to just one peripherial at a time. Upon power up after hard/soft reset, the central connects to my peripherial just fine, transfer...
Hello,
We are using the Segger Embedded Studio and trying to flash the blinky code on our nRF52DK. We have seen many videos but are unable to make it work. The code gets...
Hi,
In my memory usage, I see 780KB free from 1MB of flash. That means I am already consuming 244KB of flash when my code size is only 77KB. Obviously, there are other registers...
I have been trying to flash my nrf51822 by waveshare using my nrf 51 DK. I have been making the following connection. I am currently using P20 as the needle adapter for P19...
Dear Nordic Team,
Thanks for supporting.
Now i am try to interface(TWI) MMA8453 with nRF52810. Already i am worked with nRF52832 its working good. If possible for interface...
