Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello,
I want to test the mesh provisioning demo with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
I have encountered...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
Hi!
SDK15, s132, SD6.0.0, nRF52832
I have nRF52832 in central mode and some bonded HID devices and another nRF52832 peripherial devices.
Now in the my central nRF52832...
I simulated the balun of nrf51822 accroding to the referenced design of nrf51822 on the official website. However,it showed the differential phase of the balun was not 180...
Hello team,
We are using CPU NRF52832/810. We have followed the THINGY hardware for BLE Antenna with Ceramic Chip. Due to our range requirement more than 100 meter, we wanted...
DK : nRF52840
SDK :15.3.0
example code : nRF5_SDK_15.3.0\examples\peripheral\flash_fstorage
I watched that using nRF52840 DK is best way for develop nRF52811. So I...
Hi,
We have a product that uses nRF52832, we are trying to get the FCC Certification. We are using the RF test example to setup the DUT.
We are able to get the signals...
Hi,
I wanted to use Nordi UART service, the problem is that if I have no contraction with the device, it would not advertise after a definite time, say 180 Seconds, my devices...
