I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I read a few questions there were related to this, none that i encountered seem to give me an answer.
I am using SDK15.1 nRF52
I am NOT using dynamic allocation, I need...
Hi,
I want to connect NRF51822 wit NRF51 development kit over the air i-e. Development Kit would work as server (look for available client and connect with it and then send...
Hi,
I am using nrf51422 dk board in my project. so i need to use Bluetooth in my project. Could you plz tell me the which version of SDK do i need to use for this Bluetooth...
Hello to everyone.
I'm working with chip nRF52832 (PCA10040) and Mesh 3.1. I'm trying to connect a HC-05 Bluetooth/Serial Module using its serial pins (Rx/Tx) to the default...
Hi,
I am using SDK 15.3 and NRF52840 Preview DK
I have a requirement where I have to glow one of 3 LEDs R-G-B (each connected to one gpio pin) for 1 second and turn...
I'm using nrf52840 to develop a remote control using BLE long range.
We use two nrf52840 : on inside the remote and another in the system to control. The remote is used...
Hi,
I've done a lot of searching and Googling and could not find a proper answer for the life of me, so I'm posting again here to try to find answers. I must have looked...
I want to use internal temperature sensor in the example, "peripheral\temperature" on our software but there is the problem that we met when applying on board internal temperature...
I'm using nRF51DK and created 2 app_timers (based on LFCLK) that are running on 32.768kHz crystal, one for kernel timing (10ms) and one for real time clock (every second)...
Hi,
For some reasons, I would like to write my own application for updating the firmware, something like NRFUTIL application.
I wrote it and everything is working fine...
Hello,
I am trying the ble_app_cts_c_pca10040_s132 (current time service client). Under the conditions described below, ultimately a SoftDevice call to sd_ble_gap_device_identities_set...
I am attempting to integrate examples/peripheral/flash_fstorage into my project (SDK 14.1.0).
When calling nrf_fstorage_write I get NRF_ERROR_INVALID_LENGTH in response...
I am trying to provision 2 clients for the mesh so that i they all can send the message to a single server.
I will list what all i have tried
1.I took a server node and...
Our custom board uses internal RC clock source and I tried to build original sample app, "ble_app_pwr_profiling" in SDK 15.3.0 using attached sdk_config.h modified only with...
