Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
Hi,
I am working on a project which involves a number of low power nodes 4-16+ distributed over a relatively large area. There is one client which wants to retrieve data...
Hi. I am tinkering with BLE settings, and changed NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 7.
I then get a 0x04 error code on this function after building and running the...
I am now based on nrf52832 SDK14.2 development, nrf52832 as a peripheral device, I want to connect with IOS phone, nrf52832 provides HID Service, but when connected with Android...
I am experiencing the following compiler error:
In file included from ../../../integration/nrfx/legacy/nrf_drv_uart.c:41:0: ../../../integration/nrfx/legacy/nrf_drv_uart...
I have some question about nRF52832 Bluetooth Firmware upgrade problem:
1. I have a device with nRF52832 in my hand. If I don't use the JTag interface, how can I confirm...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
The RTC documentation states that the LFCLK source needs to be explicitly started by the software.
Is this step necessary when using the SoftDevice? As far as I know, the...
I'm not sure about how does the ble_app_att_mtu_throuthput example works exactly, i supose the throughput test runs as follows:
1 tester defines a service 'populated' with...
