Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I'm using nRF52+SDK11.0.0+S132 . It currently has SPI, SPIS, TWIM, RTC. I want to remove SPI and I'm getting: ..\components\drivers_nrf\spi_master\nrf_drv_spi.c(56): error...
Hello,
I'm using the nRF52 DK with SDK 15 and SD132 6.1.0. I have a custom service running that requires periodic characteristic writes. Occasionally when writing to this...
hi guys!
i'm trining to develop the nrf 52840 devkit in particular for the ble use.
from the documentation i didn't find anythingh about send a message to the dongle from...
Hello guys,
I am using nrf52832(PCA 10040) and transmitting radio packets. I want to collect the packets using raspberry pi. Is it possible?. If yes, how are the ways we...
Hi, everyone. I've been trying to migrate from the SDK 14.2 to 15.2, but I've been having trouble getting one new function to work. I previously used ble_advdata_set() to...
Hello,
I've checked a few related threads, but without any success.
I need to react on "Data Ready Interrupt" and read data from SPI. SPI and Device is initialized before...
I'm am trying to select an LDO to provide the VDD_GPIO power rail for the nRF9160 and am interested in selecting either a 100mA or 200mA LDO. Can Nordic provide a rough order...
Hi,
I was trying to communicate with an I2C device, which's address is 0x7C
But I always got NRF_DRV_TWI_EVT_ADDRESS_NACK event, so I took a check on the TWI wave:
...
Hi Nordic Team,
Meanwhile we are working with Laird BL654 which uses the nRf52840.
My questions:
1. Can we flash gazell examples on Laird BL654 with Segger?
2. If...
i'm trying to get distances between nrf52840 ble transmitter and receiver, using measured rssi upon receiving ble_gap_evt_adv_report_t from ble stack. in order to calculate...
In file sdk_config.h, in order to configure a calibration interval of 8 seconds, what number should be used in the define NRF_SDH_CLOCK_LF_RC_CTIV?
The time units are not...
Good day,
I again have an interesting question). There is a useful descriptor to better understand the purpose of the characteristic. This is a 0x2904 handle (GATT Characteristic...
Hi,
I want to know what event DEV KIT jump into when mobile provision complete for DEV KIT (100% , not bind app key and pub sub address). My idea is in provision process...
