hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
We would like to program the external flash connected to the nRF5340 via SWD during manufacturing.
Is this possible? Do you have any documentation that explains...
Hi
When doing a Software reset the RAM contents are persisted, however when doing a Hardware reset via nREST pin on the module then the non-initialized RAM section is...
Hi,
I am designing the ARGO module http://wizcube.eu/argo.html . I am using the excellent KiCAD library https://github.com/hlord2000/nordic-lib-kicad
It seems there is...
Hi, I'm developing a product for a client using nrf52840 which has support for DFU OTA over BLE. I'm using nrf connect sdk 2.5.0 and DFU OTA over BLE was ridiculously easy...
We're using a nRF5340 module on our board, and have basically everything working as we'd like using SDK 2.1.0.
I've tried updating to SDK 2.6.1, and managed to resolve all...
Hi,
In our new project, we are using the nRF5340 WLCSP package and configuring the system ON - low-power mode in our application code. We measured the current consumption...
Hi,
Ubuntu 20.3
vscode + nrf connect extension
when i create new application from exsample project broadcast_audio_source for nrf5340, after build, and flash into the...
Product: NRF9160
SDK: 2.6.1
Modem: 1.3.6 My problem is that FOTA download is breaking up more or less every time our device is doing a SW upgrade. We download SW directly...
NCS version : v2.6.1
target board: nrf5340dk_nrf5340_cpuapp_ns
sample project: "ncs\v2.6.1\zephyr\samples\application_development\sysbuild\with_mcuboot"
I use this command...
app and dfu works after I program the merged hex from bootloader_setting, bootloader, softdevice, app using Program application tab, but if I erase chip, reprogram it with...
Hello,
Because i want to connect more than two headset to one gateway, so i modify the prj.conf as follow
CONFIG_AUDIO_DEV =2
CONFIG_BT_MAX_CONN =4
CONFIG_BT_MAX_PAIRED...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
I using XIAO nrf52840. https://wiki.seeedstudio.com/XIAO_BLE/
I am developing a BLE peripheral device using the nRF52840. This device is designed to connect with a specific...
Hi,
Could you please advise, am designing a device using the nrf52dk-52832 in nrf sdk connect 2.5.1 and toolchain 2.5.2 that reads the previously adquired samples data from...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
