hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I am in the process of provisioning and configuring a 2-element light switch server node and a common light switch server. I am using the orginal exemple for the provisioner...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
In using the Thingy52 I can't figure out how to just get the just XY coordinates from the motion sensor - or any other sensor. I'm trying to figure out if I can capture motion...
hi, i am a student, i am new to nrf52840 DK. I downloaded Gooligmelec "nrf52test-led-battery" from github and open Solution inside SES . it was running ok. when suddenly....
Hello,
I am using nrf52840 and SDK 15.3.0. and the device wakes up every hour and every day for reporting data.
So I am using app timer to wake up also using app_timer...
Hi,
I am working on nrf52840 and using below SDK and softdevice.
SDK - 16.0
Softdevice - S140
IDE - embedded segger studio.
currently using nRF52840-DK.
I am using...
Hi Team,
We are using the Micro ECC functionalities , for that we need the SHA 256 Library,Micro ECC library won't have inbuilt SHA.So how to enable the SHA for Micro...
We are using a nordic 52840 chip with a S140 softdevice as a client to connect with GATT servers from smartphones. When we connect to one of our smartphones, we do get the...
Hi all,
i've try to update the NRF52_DK interface MCU firmware to MBED firmware (nrf5x_atsam3u2c_if_mbed_V0221_11012017.bin).
After power cycle, LD5 at interface MCU...
Any hints on connecting to HID keyboard example from linux command line ??
Running stock ble_app_hids_keyboard/pca10040/s112/ on eval board. Works fine with iPhone but can...
Hi! I'm configuring RTC on nrf51822. I'm setting up the LFCLK and RTC module by configuring their registers. I have set up a simple IRQ handler, but it seems that it never...
Hi,
I have few question on nRF9160 Thingy:91 and Dev Board.
1. From the schematic, I see that have used SP8T Switch from Antenna Feed pin (GPS and LTE) to the SIngle Antenna...