Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
I want to implement a BLE composite device with BLE UART and BLE HID, and both services can work at the same time.
Hello! I want to make a Bluetooth game controller, and...
Dear Nordic Experts.
We designed a device based on the nRF54LS05B module.
We are writing a production test program and using nRF54LS05-DK Rev 0.3.1 for verification. ...
We are using monitor mode on the nRF7002 to receive packets in promiscuous mode. We are on NCS 2.9.1. The Wi-Fi packets we receive have the follow header (struct copied from...
The nRF Thread Topology Monitor is a very useful bit of software. It would be very nice to see it updated, or perhaps even made a first-class member of the nRF Connect for...
Can you pls send recommendation document for the exact foot print to be used for nRF54LM20A-PAAA CSP98 BGA?
I have found reference foot print BGA98N35P10X10_385X367X68.dra...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
While debugging the code with Nrf connect extension in VS code , code get stuck at the start only does not go any where getting the SIGNTRAP error continuous
Hi,
With the latest SDK v 14.2 is it possible to do OTA updates to nRF52 from OSX/Windows/Linux without the use of additional DK? I understand that for iOS and Android...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
Hello, I want to use ble dfu on nordic. But most examples work with Adroid App, and I need nRFxx transmit dfu to another nordic. Can you tell me if vag has ready-made examples...
Hi,
I need to output a continuous 16 MHz clock on a GPIO pin on the nRF54L15.
I first looked at the GRTC clock output, but since the fast clock is divided by (CLKFASTDIV...
Hi, I am developing a program for the nRF54L15 with the DFU bootloader enabled. I would like to reduce the startup current.
I am using SDK 3.2.4.
The `sysbuild.conf` settings...
