Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
When I create a new build ciónfiguration in nrf connect I get this Loading and the new configuration is not created itself.
This error is displayed in the VScode.
Could...
Hello, I noticed that the SoftDevice Controller for nrf5340 in nrf Connect SDK 3.1.0 reports a bluetooth version of 6.1 (LMP Version 0x0F), yet the QDID for it ( Q360820)...
Hi,
NCS v3.4.0
BLE peripheral_uart example
nrf54l15 DK with ns config
in the Chinese (double bytes) Windows, need to add encoding="utf-8" in tfm_parse_manifest_list...
Hi,
My central device is running into Bus fault when continuously sending data to multiple connected peripheral device and any of peripheral device got disconneced. Issue...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
I hope, as a non-EE, I'm clear with my challenge ...
My student EE designed a small PCB with a couple of sensors (CO2, temp/humid, microphone) with an nRF52811. The boards...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
how to configure uart communication between nrf54l15 and tc334 via uart and i need to control my nora b2 evk leds based on mesage from tc33 using tlv can anyone give me idea...
Dear Nordic team,
Please tell me the theoretical power consumption of the nRF54L15 when using CH—both for the initiator and the reflector.
Best Regards,
Riki Yosh...
nRF91 repeatedly transitions to `+CEREG: 4` approximately every five minutes while roaming on Vodafone Germany
## setup
nrf9151 modem FW: mfw_nrf91x1_2.0.4
current SDK...
