Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
After init I2C channel
#define TWI_INSTANCE_ID 1 // because SPI0 share same reg add with TWI0 we change and enable TWI1
#define MAX_PENDING_TRANSACTIONS 5
NRF_TWI_MNGR_DEF...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
