Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, I was checking the HAL for SPI in master mode and notice that when pm_device_action_run(<spi_device>, PM_DEVICE_ACTION_SUSPEND); the CS pin isnt changed since it status...
I want to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.2.0, to hopefully get the wifi WPA Enterprise functionality to work. This is an existing...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following error message:
fatal error: nrf.h: No such file or directory
"nrf.h" is now located...
Hello, I'm using Nordic Central HR example. I'm wondering how to read RSSI of a BLE device connected to the NRF5340, I have tried multiple version found on this forum, but...
Howdy,
I am trying to connect a Waveshare BME280 to my nrf9160dk, and it's not obvious which jumper goes where. The documentation states:
Wire color
Sensor board...
hi,
i'm new with the nrf9160DK so can you please guide me to how can i start and config my nrf9160Dk with my laptop from scratch because this video is not helping me https...
Hello:
I created an app.overlay. Here it is:
/ { aliases { fra_sw = &fra_sw0; }; fra_sw0: fra_sw0 { gpios = <&gpio0 0 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; label = "FRA_SWITCH...
Hello,
We have a dual-purpose connection in our design where the signal can be either an analog input or a digital output. We have done some testing and can see that we...
Hi and Nordic forum
Please find the attached summary on the issue we are facing and help us get the guidance regarding the same
We are developing a Zigbee-based device...
Hello,
I am evaluating the nRF54L15DK current consumption based on Nordic example: https://academy.nordicsemi.com/courses/nrf54l-series-express-course/lessons/lesson-5-development...
Hi everyone, I'm thinking about implementation of SWD-over-USB with proper DAM (both CC1/CC2 pulled high). It is not totally clear to me what would be default nPM's behavior...
Hi all,
I've been troubleshooting my 9151 feather and have run into some issues with very specific AT commands. I'm trying to connect to an MQTT broker through AT commands...
Hi. I have a question about the selection of Host IC of nRF7002.
Looks like general official recommendation is nRF5340.
But my team has a long history with nRF52840...
Hi,
I'm trying to use the connection manager in my application, but it never connects or shows any events. I've tried using the https_client sample as well, but that gives...
After 9 years of work I have finally finished my product and it is FCC and EU certified, and ready for a pilot production run.
I would like to copy and paste my PCB design...
