I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
Hello,
Do you have an example that allows you to use the “Service Changed Characteristic” on the server side?
In fact, I saw on the internet that on IOS, we have to use...
Hello,
I am trying to generate encrypted data of particular data with IV and Key value by using mbedtls functions but when I try to do that in AES_CBC example code I am...
Hello,
I have multiple nrf52840 devices ( PCB's ) that act as peripherals and advertise data in BLE 5, and connectable in BLE 4.
We are able to connect to the device using...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
Hello everyone,
I am currently evaluating the nPM1300 Fuel Gauge with a LiFePo4 battery.
I would like to use nPM PowerUP to prepare the battery profile, but it appears...
hi support team,
i was testing mcumgr ota from uart, but found that the speed is slow how can i improve this?
i have change uart baud to 460800, but did not help. for...
Hi,
I'm using an nRF52840 DK to develop my prototype. Now I'm moving into the PCB design phase and I'm using a BLE ceramic antenna. I'll add a pi network footprint to tune...
I am using SPIS for my project. I am manually toggling CS for the peripheral. I get NRFX_SUCCESS for nrfx_spis_buffers_set() function. Also, when I probe the CS signal on...
Hi,
I am using the nrf52840 dongle board just to startup a project. I connected to the dongle a UART-USB converter to the dongle... but when I enable the UART into the firmware...
Hi Sir,
Please help to check do we support the ISO14064/ ISO14067 for the below part numbers.
1. Could you help to check do we pass the ISO14064/ISO14067?
If yes,...
I am implementing nrfx uarte on nRF52840 with ncs 2.6.1. I am using the example provided in modules\hal\nordic\nrfx\samples\src\nrfx_uarte as a reference.
Reason for using...
