Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi guys,
I'm pretty new in embedded development without using an Arduino. I tried to use the sensor APIs of BMI270 and BMP388 recently, but didn't get it to work.
The...
HI All,
Could you please share the details for the below s on Nordic controller MCU nRF52833-QDAA to receive quotation on BLE_SIG certification,
QDID for Link Layer...
Hi,
I have a custom board running with the nrf52832. To program it I'm using the nrf52DK board with the PCA10040 and the bootloader is based on the one found in examples...
DK : 52840
case :
we make 52840 enter active scan state and know other broadcaster devcice mac,
can we use scan filter policy filter this broadcaster devcice ,and only...
(1) I connected Nordic nRF52810 device to ipad (version: 13.5.1) (ipad uses app for connection). At this time, a pop-up window appears asking if I want to pair the devices...
Good morning. I want to take ADC 12bit/1k sampling input and send uart and bluetooth. uart works fine, but there is a problem with losing data in bluetooth transmission. ...
During testing of various combination of BLE Mesh Provisioning, I found a couple of bugs in dk_prov.c
If you Disable all OOB options for no OOB, it does not work properly...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
Hello, All
I go through datasheet of nRF5284o QFN73 IC. But i can't found which pins are used as uart /spi/i2c/pwm/timer/ I2S in pin description. Because pin assignment...
Hi,
We are using nRF Connect SDK for implementing HSL model for the BLE Mesh network consisting of RGB lights.
On comparison with nRF Mesh SDK, we found that the SDK size...
Running the ADC in continuous mode, but it seems we still have to set NRF_SAADC->TASKS_SAMPLE in a while loop. Shouldn't this not have to be set? In continuous mode we shouldn...
