hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I see the messy information elsewhere especially in selling infos about antennas for BLE5. OK optimal antenna is a quarter length of average wavelength -( 299 792 458 ) /...
I ordered nrf52-dk.
I am trying to install the SDK using nrf Connect Desktop using the option below:
Getting Started Assistant Guide to set up the nRF Connect SDK
I...
At least the combination ARM gcc 9.2.0 and nRF5 SDK 16.0.0 prevents me from doing incremental builds after some source file have changed.
The problem is with wrong dependency...
Hello,
I am developing an IEEE802.15.4 Beacon with the nRF52840-DK, SDK 16 and the nRF-IEEE-802.15.4-radio-driver . My problem is that the consumes ~400uA of current in...
Hi,
Good day,
I am having trouble for enabling the SAADC module. I keep getting the following error.
Following is the sd_config.h code
Someone help me solve this...
Hi,
I have read that using the external 32MHz crystal is mandatory for proper BLE radio operation.
However, is there any internal clock that could be used instead of the...
Hi, I am trying the to create a mesh application using iOS nRFMESH SDK. I am able to provision the device but i am not able to get data from the getCompositionData method...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
Device: nRF52832, SD132v7.0.1, NRFSDK 16.0.0
Host: nRF52840 USB BLE dongle, pc-ble-driver-py 0.14.1, Python script, Linux
We're developing a device that's a BLE Peripheral...
Hi, I am looking for any suggestions on heart rate sensors i can use that would easily integrate with the nrf52832. I am looking to get a finalized output from the heart rate...
Hi I have a few questions about bluetooth 5.1 and the CTE packets that it transmits.
1. I know that there is a physical difference in the hardware of a Bluetooth 5.0 chip...
