Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hi All, I am using an nrf52832 and using NCS version 2.6.0. I am having an issue where I am trying to initialize and run a thread, but the thread never runs. I have tried...
I want to set the CONFIG_CAF_BLE_ADV_FAST_ADV Kconfig option to make the Peripheral initially advertise with a shorter interval,but after adding some dependency configurations...
hello.
Currently I am implementing BLE Multi advertising in
NCS SDK: version 2.6.0.
I have a question during development through the samples/bluetooth/multiple_adv_sets...
Hello,
I am working with the USB CDC ACM Sample Application from NCS V2.1.0 on nRF52840DK and have encountered an issue when attempting to replace the UART_INTERRUPT_DRIVEN...
Hello,
I am writing to seek clarification on the difference between AT%XRAI and AT%RAI. I was testing the RAI feature using the SLM application (SDK v2.7.0 and modem firmware...
trying to program an nRF51422 chip with Segger embedded studio with soft device
i get the error
"Checking project status Building ‘ble_app_uart_c_pca10028_s130’ from solution...
Hello,
I have a custom board running as a low power node, consuming around 17uA during sleep. When I have messages back and forth, the node goes back to sleep as usual....
Dear support team: Problem description: Use \v2.7.0\nrf\samples\bluetooth\mesh\light routines to download to nRF52840-DK board, after adding it with nRF Mesh app (Android...
Hello,
I have trouble again with TX Power control. This time using Softdevice Controller and NCS2.6.0.
Previous issue which was solved (this was using Zephyr Controller...
I'm working on a Proteus-III module which needs to communicate with the on board UART0. For reasons that I still don't understand, the `uart_configure` function with which...
I would like to test event related functions on nRF5340 DK. But west build failed with undefined reference to `z_impl_k_event_init'. The following are log messages of west...
Hi,
I am trying to connect 4 devices (2 nrf devices + 2 B24 custom modules). Each of them can get connected independently as single device, but as soon as I start connecting...
I'm reading the code of peripheral_hids_mouse project and I want to select some functions to fill my own code.
prj.conf has these two config:
CONFIG_BT_GATT_UUID16_POOL_SIZE...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
