I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
I am using NRF52833 and trying to setup DFU specifically for OTA.
As experienced in other threads the size limitations are there
Secure_Boot builds creating slot partitions...
Howdy guys,
I am using an nrf52840 and SDK version 17.1.0 alongside Keil. I just upgraded from using the arm compiler version 5 to 6, which required me to switch from the...
Hi,
I have an implementation in which two boards communicates through ble and i want to measure the throughput of both. The behaviour that I see is that increasing the connection...
Hi,
I have a Tuya FingerBot Plus and when using the Zigbee Shell sample:
1.I can 'click' the finger using a ZCL command
2. I can't change the 'finger mode' from 'click...
Hello
I have 2 devices ,a central and a peripheral on a custom nRF52840 board
Using Zephyr SDK 2.5.0
The distance between the devices is 10.9 meters. When TX power on...
Hello,
We have nRF52833 on the custom board, now we want to do DFU over Bluetooth. During my initial research reults with following questions:
If you use 1. " nRF Connect...
Hi, Everyone
I have space constraint in my round PCB for RF section where i have take referance from thingy91 board and choose the same components exept mcu is nrf5340 claa...
Hi,
I have a request to port an old code into Zephyr. The code uses a proprietary protocol and the radio has been developed on bare metal under a nRF52832 chip. There is...
Hi all,
I am evaluating ANT+ features in nRF52 DK board and I am using nRF5_SDK_17.1.0_ddde560 SDK.
I need to implement ANT+ Bicycle light profile (LGT) in my device....
Hi.
I'm developing a ble module now.
I have a question about time out, interval among BLE init Advertising.
As shown in the picture below, time out (in units of 10ms...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZED)
NCS v2.4.1
Hi,
I am working on Tunneling cluster handling as that one...
Development environment: ncs 2.6.0.
my application need BLE-DFU, so i added multi-image support to my project.
the pm_static.yml is the typical default system configuration...
Hello,
I am working on a SWD flasher for nRF52 chips. I try to perform basic commands like flashing a firmware or reading flash content. I wanted to use FICR informations...
I am using NCS V2.6.0 and using zephyr there is no examples to measure battery level using saadc we can measure the battery level right? I used LEDs to indicate battery level...
