Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Triggering advertising by button pressed. But when advertising state is not idle. Both sd_ble_gap_adv_set_configure() and ble_advertising_start() failed with errCode 0x8....
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I am using a function in my source code that reads the current RSSI of the connection. The function, read_conn_rssi...
Hi there,
I am trying to implement the OTA DFU feature via Zigbee in my product. i tried to implement the example available in SDK as below https://infocenter.nordicsemi...
We are able to build nrf5340_audio application with SBC codec,
but error occurs when program the app core with buildprog.py
dongtaotao@dongtaotao-OptiPlex-5070:~/ncs_v2...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Greetings,
In our product, we encountered an issue when data saved in flash (FDS) that were previously retained are erased during DFU on some devices . This was indeed fixed...
Hi, I'm building an applicaiton based on ble_app_uart. I got that using idle_state_handle(); function to set the my nRF52833 into system ON mode. I disable system OFF mode...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
Hi,
We are using ANNA-B112 module with nRF52832 chip and trying to store the product serial number in UICR. From the description of UICR, it seemed that the CUSTOMER area...
Hi,
A have an application on a custom board that will not start, unless I use JFlash Start Application command, or attache the debugger. I already added CONFIG_BOARD_ENABLE_DCDC...
Hi,
given "nrf_drv_twi_xfer" or its "nrfx_twim_xfer" younger brother is used to communicate over I2C, and its a TxTx tranfer, than what does "nrf_drv_flag_tx_no_stop"...
I am using bleak and python to connect to a ble device and then using subprocess to run the dfu. The ble device disconnects when the dfu starts and then I get "Connection...
