I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi Team,
I am trying to make RTT in debug terminal instead of debug serial port i was add all rtt files in the project tree but it was not shown in cmsis configure wizard...
Hello everyone,
I am trying to implement ECDSA_P256 in my code by using the nrf_oberon libraries.
What I have to configure in order to use these functions?
Regards ...
I use nRF52810 SoC to forward data between BLE and UART on our product. So I initialize UART interface and set some GPIOs once enter the "main" function in my codes. But we...
Sdk: 1.6
Modem fw: 1.3
Hi,
I am testing the GPS + supl example on our custom board. I am sitting indoor close to a window so satellite reception is affect.
the example...
Hello,
I am Working on the nRF52840 custom board.
To drive the motor and buzzer I am using a PWM driver in that when I set duty-cycle 20 percent then the output of PWM...
Hi guys,
Using the PPK 2 board I have noticed that sometimes my device does not go into deep sleep mode between two tasks. I had to implement a lot of flash operations using...
Hi Team,
Currently we are using 52840 soc with softdevice s140_nrf52_7.0.1_softdevice.hex.
We want to migrate to 5340 for BLE 5.2 features, we would like to understand...
Hi,
I need the SAADC of the nRF52840 to do the following:
It should sample two channels as fast as possible for a certain time (or for a certain amount of samples)....
Hello,
I have tried to upgrade a working project from ncs 1.5.0 to 1.6.0, which used the shell + console + RTT. However, long commands (more than 16 chars) seem to be truncated...
Device: nRF5340 DK
I installed the SEGGER Embedded Studio and wanted to run a sample application. But it throws an error when I click on Connect J-Link.
But I see that...
Dear friends,
When I reset 52840 DK and reopen the PyACI script , then, reloading the DB(database/example_database.json), I found the provsioned device can't be controled...
Hi sir/Madam,
Kindly provide the uplink and downlink details for the part
nRF9160.
We request you to provide the quote for 50K/Annum.
Please contact : lakshminarayanan...
Hi,
I am aware that the sdk-nrfxlib + sdk-nrf library embed a NFC library, dedicated to a ST NFC module.
In our product, we are using a NXP controller, a PN7150.
Is...
Hi everyone,
I got a question regarding the Bluetooth Mesh Time Server/Client models. I would like to propagate a common time base within my Bluetooth Mesh network by using...
I use the NCS SDK 1.5.1, the sample is use a QSPI FLASH(MX25R64), and we want to change this QSPI FLASH. we will use P25Q80H, which code should be modify?
