I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
I need to make a reset of mesh device with clearing its configuration.
For this I tried to use model_config_file_clear() or mesh_stack_config_clear() functions.
However...
Hi,
How to enable fast mode for radio transmission and reception (I am using nRF5 SDK). These are the default examples and I can see that fast mode is not implemented: ...
Hello again,
I saw this Github 's post and I was wondering if is possible to use some of the libraries and drivers with nRF52811 and if so should I pay attention to some...
Hi,
Question:
In our project we need to drive some external components (High Side Drivers) via GPIO output.
In order switch on our “High Side Drivers” we need a voltage...
I'm using TWI and BLE functions together. My TWI sensor is operating at 400kHz, low priority. BLE has the highest priority. For example, if nRF52805 is sending commands to...
Hello community, I tried to read my motor encoders with the QDEC and capture the position of my motor. Hardware: nRF52840 DK, 2 Hal motor encoders on pin 0.13 and 0.14 which...
In NCS v1.6.99 the HEX data format is removed from data send and receive commands (socket, udp/tcp cli/srv), only ascii and data mode is supported.
In case of binary data...
Hello,
First time post and brand new to the nRF52832 chip. I am tasked with building firmware that will synchronize ADC samples across multiple devices. I have started with...
Hi to all team,
I have two units of nrf52840 dongle with me.
I have to develop the generic application firmware where data send from one dongle(coordinator) is getting...
Hi,
I have built ble board with nrf52832 with no pca10040 on my board and i have assign button switch pin as P.0.13 from nrf52832.Previously i am using nrf52832 dev kit...
Hello,
I have a custom example based on the "asset_tracker" application of the SDK v1.3.1 and I am trying to open the IDE through Toolchain Manager, but when I select "OPEN...
hi support team,
i was testing usb dfu(NCS1.6.0) function with window10, after i download the code, the windows seems not able to install the driver as below, and i couldn...
Just a naive question about the definition of nrf_fstorage_t , it has a member nrf_fstorage_info_t *p_flash_info .
Why the type isn't nrf_fstorage_info_t const* ?
Tell...
Hi,
there should be OK response after #XSLEEP before enter into sleep to notify, that command was received and processed without errors.
Current implementation (NCS v1...
