I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
I'm using nRF52832 with an external motion co-processor. As a part of a robust reset strategy, I want to connect a single nRF52 pin to the co-processor's nRST pin to generate...
Hi
I'm using NCS 1.4.0 and SES. If I change the setting in Serial LTE modem to CONFIG_SLM_CONNECT_UART_2 for external MCU connection, I get an error msg from SES: Cannot...
Hello,
I am using "nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730" for NCP as well as other thread devices. nrfutil version: 5.2.0 RPI3 image: RaspPi_OT_Border_Router_Demo_v3...
I'm running OpenThread on a nrf52840-mdk from maker diary. I'm using the nRF SDK for thread and zigbee.
I would like to poll a sensor periodically. OpenThread does not offer...
hi support team,
i found that 52833 UART power is different from 832,
in SDK17.0.2,
832 is still 1.15 mA(with DMA), however 833 is about 0.437 mA(with DMA),
832 is...
Hello,
I want to use the BLE UART example on my PCA10040 development board, but I can´t transmit or receive any data from my PC to the smartphone with the nRF Connect app...
Hi all,
I have a question.
When I try send message coap, it can send as mesh network.
But when I send search gateway msg, connect msg from publish (subscribe) Node to...
My custom nRF9160 board does not communicate with nRF Connect Programmer.
"Unsupported device. The detected device could not be recognized as neither JLink device nor Nordic...
Hello everyone!
I have some issue with the comparator module on the nrf52820 chip.
We need to compare one of external analog signal the 1.8V internal reference source...
Hi,
I try to achieve high throughput via BLE connection between two nRF82540dk boards. I would like to maximize duty cycle of transmission in the connection interval. Unfortunately...
I am sending 240-byte data from peripheral to central through notification (without response) by using the ble_nus_data_send() function when the BLE_NUS_EVT_TX_RDY event comes...
Hi,
I received source code and compiled .hex file from Visual GDB from previsou developer.
I would like to continue development in Segger Embedded Studio.
I know the...
hi support team.
i want to use time from ntp server, and we have example in nrf/lib/data_time;
after devzone searching, i added below setting to prj.config
CONFIG_DATE_TIME...
Hi, I am trying to send data from one peripheral to a central unit and then relay the message to another peripheral unit over BLE. The peripheral already sends the data to...
Hi,
I'm trying to reinitialize my ANT stack, after update of parameters which is done by BT. To be exact, I'm setting the ANT ID of the ANT device that will send data to...
