Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I am running the ADC demo for the 52833-DK (pca10100) and can’t seem to get any valid readings. SDK 16.0: examples\peripheral\saadc
I am applying 1.5V to AIN0 on P8 and...
Hi, I am developing something using Zephyr on a nRF52840-DK as one Bluetooth mesh node and a Thingy as the other. To program the Thingy, I have it connected the Thingy to...
Hello -
I am trying to run the USB CDC ACM example on macOS 10.12.6. Following the instructions in the example app, I should see a virtual COM port as /dev/ttyACMx when...
Hello,
I am doing some testing on the nrf52832 DK using the mesh light switch example, i am sending ACK messages, i would like to log the time it takes the message to reach...
Hi,
What is the proper way to set "real time" in nRF9160 with nRF Connect SDK?
I want the function time() from the file time.h to return the correct time.
I know that...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
Dear Nordic
I am using SDK14.2, I cannot pint info . SDK periphral uart and serial can't print also
nus example jlinkrtt print as below:
<00> warning> nrf_sdh_ble: RAM...
Hi,
I am using pc-ble-driver version 4.1.1 with the SD version 6.1.1.
I want to configure the TX power for the NRF52 USB dongle.
Do you have a code example for configuring...
Now I can build & download nRF52840 SDK example with Eclipse.
But Eclipse indexer(F3 key) can not recognize include folder.
So I added every include folder to .cproject...
I'm having a advertising device and then I want to stop advertising and prevent BLE connection from device that would have received the advertisement. It seems to work by...
Dear Team,
I am trying to add my Thingy 91 to nRF cloud, but I receive the following error :"There was an error adding your device: No device found with id 'nrf-xxxxx'....
Hi Nordics
https://devzone.nordicsemi.com/f/nordic-q-a/22595/can-not-received-ble_gap_evt_timeout-event-when-connect-timeout/88877#88877
Referring to the above post, I...
Dear,
I am trying to test BLE on the THINGY:91.
Follow the Q&A for "Introduction to Nordic THINGY:91" webinar, Q12 of @ Petter Myhre
I tried with Zephyr HCI UART example...
