I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
Just to share my though here.
I think it is better way to decouple the BLE and application with dual core design.
It help to get rid of application latency due to...
Hello Everyone,
We have 2 devices. 1st device is flashed with the Eddystone example & sending TLM info. The 2nd device is flashed with a modified version of the ble_app_hrs_c...
Hi.
So I'm trying to configure my SW to use two uarts (as I've understood that uarte and uart are separate modules that can be used at the same time).
As the app_uart...
Dear nordic,
I implemented a uart in BLE application its works fine.
I need to reduce current for that i enable and disable uart but when i call function disabled or enabled...
hi team,
real quick; The accuracy internal reference (0.6V) used in the SAADC is specified in COMP section of the data manual as +/-3%. The gain error in the SAADC is...
Hi,
I was just trying to build the light_switch_provisioner_nrf52840 code using Segger Embedded Studio. However, I've got a error build/light_switch_provisioner_nrf52840_xxAA_s140_6...
What is the function of db_discovery_init (); , I am migrating a code from SDK 8 to SDK 14.2 and I can not find that function, I do not know what library it contains or how...
Hi Nordic.
I am currently working on nRF52810 chip and the main power source is lipo battery. The battery is charged via USB could you recommend an efficient power management...
Hi,
I am currently migrating my controller from nRF51 to nRF52832 . I am facing an issue where in when I try to do an TWI communication with MPU9250 on nRF52 the code gets...
Hey
all process of burning work great without use of reset pin.
question is do we need to change it and wire pin to jtag connector?
what is the added value of the pin...
Hi All,
I have been using Keil but have decided to test "Seggers Embedded Studio for ARM" to develop firmware for the NRF51822. After following this tutorial i have been...
Hi,
We were working on a board that communicates with another board from a customer. It seems that the customer's board has voltage spikes sometime (it has 110 VAC signals...
We create general purpose device based on nrf52840 chip and need to provide different ways of dfu: buttonless, usb, uart. Is there any examples, recommendations how to do...
NRF52840 = GCC/GNU ARM - SDK 15.0 - SD 6.0.0 - Builds tested under windows & linux on two separate machines. Chip is Fanstel BT840E-V2 module on a custom board. We've been...
